Showing 97–108 of 206 results
CN6009 / XL6009 DC-DC Adjustable Step-Up Boost Converter Module
Technical Specifications
| Characteristic | Specification Parameters |
|---|---|
| Converter Circuit Topology | Non-Isolated Step-Up Boost Regulator |
| Input Supply Voltage (VIN) | 3.0V to 32.0V DC (Optimal performance configuration begins at 5.0V) |
| Adjustable Output (VOUT) | 5.0V to 35.0V DC (Output voltage must remain higher than input) |
| Switch Output Current Limit | 4.0A Maximum peak load tracking current (Continuous output rated at 2.0A–3.0A without external cooling) |
| Fixed Internal Clock | 400 kHz Switching Frequency |
| Maximum Efficiency Profile | Up to 94% Conversion Performance |
| Output Ripple Voltage | ~50 mV to 100 mV peak-to-peak frequency ripple |
| Chassis Main Dimensions | Approx. 43 mm × 21 mm × 14 mm |
CP2102 USB to TTL Serial Converter Module
Technical Specifications
| Characteristic | Specification Parameters |
|---|---|
| Core Controller IC | Silicon Labs CP2102 USB-to-UART Bridge |
| Physical Input Interface | Micro-USB, Mini-USB, or Type-C Female Port (Variant dependent) |
| Supported Transfer Rates | 300 bps up to 1 Mbps full hardware speed matching |
| Signal Logic Threshold | 3.3V TTL Logic (Inputs are safely 5V tolerant) |
| Onboard Voltage Outputs | 3.3V DC (up to 100mA max) and 5.0V DC (up to 500mA with self-resetting fuse) |
| Integrated Hardware Buffer | 512-byte receive buffer and 512-byte transmit buffer |
| Module Outer Dimensions | Approx. 26 mm × 15 mm × 11 mm (Ultra-compact form factor) |
CP2102 USB to TTL Serial Converter Module 6-pin (Black PCB Edition)
Technical Specifications
| Characteristic | Specification Parameters |
|---|---|
| Core Protocol Chipset | Silicon Labs CP2102 USB-to-UART Bridge Controller |
| PCB Soldermask Color | Matte Black / Glossy Black |
| PC Input Connector | Standard USB Type-A Male Interface |
| Data Rate Range | 300 bps up to 1.0 Mbps or 1.5 Mbps stable operations |
| Internal Data Buffers | 512-Byte Receive Buffer / 640-Byte Transmit Buffer |
| Logic Signal Voltage | 3.3V TTL Level Logic (Inputs are safely 5V tolerant) |
| Module Length & Width | Approx. 42 mm × 15 mm |
CR1220 Lithium Manganese Dioxide Coin Cell Battery
Technical Specifications
| Characteristic | Specification Parameters |
|---|---|
| Battery Chemistry Core | Lithium Manganese Dioxide (LiMnO2) Primary Cell |
| IEC Standard Designation | CR1220 (Cross-references with DL1220, ECR1220, BR1220) |
| Nominal Voltage Output | 3.0V DC |
| Average Charge Capacity | 35 mAh to 40 mAh |
| Standard Continuous Drain | 0.1 mA |
| Cell Structural Diameter | 12.5 mm |
| Cell Structural Thickness | 2.0 mm |
| Average Component Weight | Approx. 0.8 grams to 1.0 gram |
CR2032 Lithium Manganese Dioxide Coin Cell Battery
Technical Specifications
| Characteristic | Specification Parameters |
|---|---|
| Battery Chemistry Core | Lithium Manganese Dioxide (LiMnO2) Primary Cell |
| IEC Standard Designation | CR2032 (Cross references with DL2032, ECR2032) |
| Nominal Voltage Output | 3.0V DC |
| Average Charge Capacity | 220 mAh to 240 mAh |
| Standard Continuous Drain | 0.2 mA (Peak pulse capacity up to 15 mA) |
| Cell Structural Diameter | 20.0 mm |
| Cell Structural Thickness | 3.2 mm |
| Average Component Weight | Approx. 3.0 grams |
DRV8825 Microstepping Stepper Motor Driver Module
Technical Specifications
| Characteristic | Specification Parameters |
|---|---|
| Driver Driver IC | Texas Instruments DRV8825 Motor Driver |
| Motor Driving Voltage (VMOT) | 8.2V to 45.0V DC (External motor power feed) |
| Logic Working Voltage | 0V to 5.5V DC (Does not require a separate VCC logic pin) |
| Continuous Output Current | 1.5A per phase winding (Up to 2.2A with active cooling fan/heatsink) |
| Microstep Resolutions | Full-step, 1/2, 1/4, 1/8, 1/16, and 1/32 steps (3 Selectable Pins) |
| Hardware Safety Checks | Over-temperature shutdown, over-current fault, and short-circuit protection |
| Module Dimensions (approx.) | 20 mm × 15 mm × 11 mm |
DRV8833 Dual H-Bridge DC Motor Driver Module
Technical Specifications
| Characteristic | Specification Parameters |
|---|---|
| Driver Driver IC | Texas Instruments DRV8833 Dual H-Bridge Chip |
| Motor Supply Voltage (VM) | 2.7V to 10.8V DC (Ideal for Li-Ion, NiMH, or AA battery packs) |
| Continuous Output Current | 1.2A per individual motor channel (at 25°C room temperature) |
| Peak Pulse Current Limit | 2.0A per channel for short pulse durations |
| Control Logic Input Level | 3.3V and 5V Logic Compatible (Works with Arduino, ESP32, Raspberry Pi) |
| PWM Frequency Support | Up to 50 kHz for smooth speed adjustments |
| Module Dimensions (approx.) | 18.5 mm × 16 mm × 3.5mm |
Dual Shaft BO Motor – (Battery Operated Geared DC Motor)
Technical Specifications
| Characteristic | Specification Parameters |
|---|---|
| Motor & Gearbox Type | Permanent-Magnet Brushed DC Motor with Plastic Spur Gears |
| Operating Voltage Range | 3.0V to 9.0V DC (6V DC Nominal Standard) |
| Common Rated Speeds | 60 / 100 / 150 / 200 / 300 RPM (Depending on Voltage) |
| Current Draw Profile | ~60mA No-Load Current / ~700mA at full mechanical stall |
| Output Torque (approx.) | ~0.35 kg-cm up to 1.9 kg-cm (Ratio-dependent scaling) |
| Shaft Profile & Shape | Slotted Flat-Sided Dual Output Axles (5.5 mm to 6 mm Diameter) |
| Casing Dimensions | 55 mm × 48 mm × 23 mm |
Dual-Axis PS2 Joystick Breakout Module
Technical Specification Details
| Parameter | Specification Details |
|---|---|
| Operating Input Supply | 3.3V to 5.0V DC (Logic-level matched to host microcontroller) |
| Potentiometer Resistance | Dual 10kΩ linear potentiometers (X and Y axes) |
| Output Type Profile | 2 × Analog Voltage Outputs (VRx, VRy) | 1 × Digital TTL Output (SW) |
| Center Bias Point | Outputs approximately VCC / 2 when at rest in the center position |
| Switch Operation Style | Momentary tactile switch (Needs a pull-up resistor, outputs LOW when pressed) |
| Operational Lifespan | Rated for more than 1,000,000 cycles of structural deflection |
| Physical Proportions | 40.0 mm × 26.0 mm × 32.0 mm |
Duracell Alkaline AA 1.5V Battery
The Duracell Alkaline AA 1.5V Battery (commonly searched for via typo as "AA batery durecell") is a high-performance, single-use cylindrical power cell engineered to drive both high-drain electronics and everyday household gadgets. Utilizing premium Alkaline-Manganese Dioxide chemistry, it provides up to 10 times longer lasting power compared to standard zinc-carbon batteries. Recognizable by its iconic "Copper Top" black and bronze design, it serves as the premium power solution across India for digital cameras, motorized toys, game controllers, and flashlights. [1, 2, 3, 4, 5]
✨ Key Features
- Duralock Power Preserve Technology: Formulated to lock in chemical energy, guaranteeing a shelf life of up to 10 years in proper storage conditions.
- Superior Leakage Prevention: Built with a robust mechanical top closure and specialized anti-corrosion steel casing to prevent dangerous runtime leaks.
- High-Drain Optimisation: Capable of supplying consistent voltage without dropping under sudden high-current load pulses.
- Wide Thermal Tolerance: Specially designed to operate smoothly across a wide temperature spectrum, maintaining efficiency in extreme environments.
Duracell Ultra Alkaline AA 1.5V Battery
Technical Specifications
| Characteristic | Specification Parameters |
|---|---|
| Battery Chemical Profile | Premium High-Performance Alkaline Manganese Dioxide (Zn/MnO₂) |
| Global Standard Sizing | AA / LR6 / MX1500 / 15A |
| Nominal Output Voltage | 1.5V DC |
| Internal Static Impedance | ~81 m-Ohm @ 1 kHz |
| Average Rated Capacity | ~1,500 mAh down to a 0.8V cut-off threshold |
| Operating Temperature | Reliable performance from -20°C up to 54°C |
| Rechargeable Attributes | No (Strictly single-use disposable; attempting to charge may explode) |
| Average Unit Component Weight | Approx. 24.0 grams to 25.0 grams per cell |
ESP32 NodeMCU 38-Pin Development Board
Technical Specifications
| Characteristic | Specification Parameters |
|---|---|
| Microprocessor Core | Xtensa Dual-Core 32-bit LX6 Architecture (Up to 240 MHz) |
| Memory Capacity | 520 KB SRAM / 4 MB SPI Flash Memory |
| Wireless Protocols | Wi-Fi 802.11 b/g/n + Bluetooth v4.2 BR/EDR & BLE |
| Logic Voltage Level | 3.3V DC (Inputs are not 5V tolerant) |
| Input Supply Limits | 5.0V DC via Micro-USB or 5.0V to 9.0V DC via Vin pin |
| USB-Serial Chipset | CP2102 or CH340 USB-to-UART Bridge controller |
| Module Frame Footprint | Approx. 55 mm × 28 mm × 13 mm (Slightly longer form factor) |
