Showing 73–84 of 214 results
60 RPM 12V DC Centre Shaft Geared Motor
Technical Specifications
| Characteristic | Specification Parameters |
|---|---|
| Motor Type | Brushed DC Motor with Metal Spur Gearbox |
| Operating Voltage | 6.0V to 24.0V DC (12V DC Nominal Output) |
| Base Speed (at 12V) | 60 RPM |
| Rated Stall Torque | 4 kg-cm to 5 kg-cm |
| No-Load / Load Current | 60 mA (Max) / 300 mA (Max) |
| Shaft Dimensions | 6 mm Diameter with internal M3 tapped hole |
| Main Frame Dimensions | 35 mm Gearbox Diameter × 72 mm Overall Body Length |
6V 1A DC Power Adapter
Technical Specifications
| Characteristic | Specification Parameters |
|---|---|
| Input AC Voltage Range | 100V AC to 240V AC (Standard Domestic Home Grid) |
| Input AC Frequency | 50 Hz / 60 Hz |
| Output DC Voltage | 6V DC Fixed |
| Maximum Output Current | 1.0 Ampere (1000 mA) Continuous |
| Total Rated Power Capacity | 6 Watts Max |
| Connector Dimension Profile | Usually 5.5 mm × 2.1 mm (Variant dependent) |
| Connector Core Polarity | Center-Positive (Inner pin (+), Outer ring (-)) |
| Energy Efficiency Grade | Level VI compliance (ultra-low standby energy loss) |
6V 2A DC Power Adapter
Technical Specifications
| Characteristic | Specification Parameters |
|---|---|
| Input AC Voltage Range | 100V AC to 240V AC (Standard Domestic Home Grid) |
| Input AC Frequency | 50 Hz / 60 Hz |
| Output DC Voltage | 6V DC Fixed |
| Maximum Output Current | 2.0 Amperes (2000 mA) Continuous |
| Total Rated Power Capacity | 12 Watts Max |
| Connector Dimension Profile | Standard 5.5 mm × 2.1 mm (Variant dependent) |
| Connector Core Polarity | Center-Positive (Inner pin (+), Outer ring (-)) |
| Circuit Design Type | Switched-Mode Power Supply (SMPS) |
7.5V 1A DC Power Adapter
Technical Specifications
| Characteristic | Specification Parameters |
|---|---|
| Input AC Voltage Range | 100V AC to 240V AC (Standard Single-Phase Domestic Mains) |
| Input AC Frequency | 50 Hz / 60 Hz |
| Output DC Voltage | 7.5V DC Fixed |
| Maximum Output Current | 1.0 Ampere (1000 mA) Continuous |
| Total Rated Power Capacity | 7.5 Watts Max |
| Connector Dimension Profile | Usually 5.5 mm × 2.1 mm (Check device requirements) |
| Connector Core Polarity | Center-Positive (Inner pin (+), Outer ring (-)) |
| Circuit Design Type | Switched-Mode Power Supply (SMPS) |
9V 1A DC Power Adapter
Technical Specifications
| Characteristic | Specification Parameters |
|---|---|
| Input AC Voltage Range | 100V AC to 240V AC (Standard Single-Phase Domestic Mains) |
| Input AC Frequency | 50 Hz / 60 Hz |
| Output DC Voltage | 9V DC Fixed |
| Maximum Output Current | 1.0 Ampere (1000 mA) Continuous |
| Total Rated Power Capacity | 9 Watts Max |
| Connector Dimension Profile | Standard 5.5 mm (Outer Diameter) × 2.1 mm (Inner Pin Diameter) |
| Connector Core Polarity | Center-Positive (Standard) / Check Pedal exceptions |
| Circuit Design Type | Switched-Mode Power Supply (SMPS) |
9V 2A DC Power Adapter
Technical Specifications
| Characteristic | Specification Parameters |
|---|---|
| Input AC Voltage Range | 100V AC to 240V AC (Standard Domestic Home Grid) |
| Input AC Frequency | 50 Hz / 60 Hz |
| Output DC Voltage | 9V DC Fixed |
| Maximum Output Current | 2.0 Amperes (2000 mA) Continuous |
| Total Rated Power Capacity | 18 Watts Max |
| Connector Dimension Profile | Standard 5.5 mm (Outer Diameter) × 2.1 mm (Inner Pin Diameter) |
| Connector Core Polarity | Center-Positive (Standard) / Check music gear exceptions |
| Circuit Design Type | Switched-Mode Power Supply (SMPS) |
A4988 DMOS Microstepping Stepper Motor Driver Module
Technical Specifications
| Characteristic | Specification Parameters |
|---|---|
| Driver Driver IC | Allegro A4988 Microstepping Driver Chip |
| Motor Supply Voltage (VMOT) | 8.0V to 35.0V DC (External power rail for driven actuators) |
| Logic Supply Voltage (VDD) | 3.0V to 5.5V DC (Fully compatible with 3.3V and 5V microchips) |
| Continuous Output Current | 1.0A per phase winding (Up to 2.0A with attached heatsink and active cooling) |
| Microstep Resolutions | Full-step, Half-step, Quarter-step, Eighth-step, and Sixteenth-step |
| Onboard Fault Protection | Thermal shutdown, crossover-current protection, and under-voltage lockout |
| Module Dimensions (approx.) | 20 mm × 15 mm × 11 mm (Ultra-compact DIP carrier form factor) |
ACS712 Current Sensor Module – 10A
Technical Specification Details
| Parameter | Specification Details |
|---|---|
| Primary Sensor IC | Allegro MicroSystems ACS712 |
| Sensing Engine Mechanism | Linear Hall-Effect Sensor Array |
| Operating Input Supply | 5.0V DC Single Supply (Power LED Indicator Onboard) |
| Conductor Path Resistance | Low 1.2 mΩ internal resistance path |
| Output Type Profile | Ratiometric Analog Voltage (0.5V to 4.5V output window) |
| Zero Current Bias Point | VCC / 2 (Approximately 2.5V DC) |
| Module Sensitivities | 10A Variant: 195 mV/A |
| Total System Accuracy | 1.5% Error Index threshold calibration at room temperature |
| Physical Dimensions | 31.0 mm × 13.0 mm × 13.5 mm low profile |
ACS712 Current Sensor Module – 20A
Technical Specification Details
| Parameter | Specification Details |
|---|---|
| Primary Sensor IC | Allegro MicroSystems ACS712 |
| Sensing Engine Mechanism | Linear Hall-Effect Sensor Array |
| Operating Input Supply | 5.0V DC Single Supply (Power LED Indicator Onboard) |
| Conductor Path Resistance | Low 1.2 mΩ internal resistance path |
| Output Type Profile | Ratiometric Analog Voltage (0.5V to 4.5V output window) |
| Zero Current Bias Point | VCC / 2 (Approximately 2.5V DC) |
| Module Sensitivities | 20A Variant: 100 mV/A |
| Total System Accuracy | 1.5% Error Index threshold calibration at room temperature |
| Physical Dimensions | 31.0 mm × 13.0 mm × 13.5 mm low profile |
ACS712 Current Sensor Module – 30A
Technical Specification Details
| Parameter | Specification Details |
|---|---|
| Primary Sensor IC | Allegro MicroSystems ACS712 |
| Sensing Engine Mechanism | Linear Hall-Effect Sensor Array |
| Operating Input Supply | 5.0V DC Single Supply (Power LED Indicator Onboard) |
| Conductor Path Resistance | Low 1.2 mΩ internal resistance path |
| Output Type Profile | Ratiometric Analog Voltage (0.5V to 4.5V output window) |
| Zero Current Bias Point | VCC / 2 (Approximately 2.5V DC) |
| Module Sensitivities | 30A Variant: 66 mV/A |
| Total System Accuracy | 1.5% Error Index threshold calibration at room temperature |
| Physical Dimensions | 31.0 mm × 13.0 mm × 13.5 mm low profile |
ACS712 Current Sensor Module – 5A
Technical Specification Details
| Parameter | Specification Details |
|---|---|
| Primary Sensor IC | Allegro MicroSystems ACS712 |
| Sensing Engine Mechanism | Linear Hall-Effect Sensor Array |
| Operating Input Supply | 5.0V DC Single Supply (Power LED Indicator Onboard) |
| Conductor Path Resistance | Low 1.2 mΩ internal resistance path |
| Output Type Profile | Ratiometric Analog Voltage (0.5V to 4.5V output window) |
| Zero Current Bias Point | VCC / 2 (Approximately 2.5V DC) |
| Module Sensitivities | 5A Variant: 185 mV/A |
| Total System Accuracy | 1.5% Error Index threshold calibration at room temperature |
| Physical Dimensions | 31.0 mm × 13.0 mm × 13.5 mm low profile |
Aerol Contact & Component Cleaner Spray – Grade 8003
Technical Specifications
| Specification | Details |
|---|---|
| Brand | Aerol |
| Product | Contact & Component Cleaner |
| Grade | FM8003 / 8003 |
| Type | Aerosol Spray |
| Application | Electrical & Electronic Cleaning |
| Net Content | 500 ml |
| Net Weight | Approx. 334 g |
| Form | Liquid Spray |
| Color | Water White |
| Evaporation | Fast Evaporating |
| Residue | Non-residual |
| Applications | PCB, connectors, contacts, switches, relays, electronic components |
