Name: PL2303 USB to TTL Serial Converter Cable
SKU: VE-130
Availability: InStock

PL2303 USB to TTL Serial Converter Cable

Technical Specifications

Characteristic	Specification Parameters
Embedded Controller IC	Prolific Technology PL2303HX / PL2303TA / PL2303GS
Host Computer Port	Standard USB Type-A Male Interface
Cable Length Profile	Approximately 1.0 Meter (3.3 Feet)
Logic Signal Threshold	3.3V TTL Level Logic (Standard model assignment)
Integrated Power Output	Fixed 5.0V DC output path pulled from host USB port
Supported Baud Rates	300 bps up to 1 Mbps or 6 Mbps (Depending on PL2303 generation)
Wire Terminal Interface	4 Pin Individual Female JST/Dupont Receptacles

SKU: VE-130 Category: Converters

The PL2303 USB to TTL Serial Converter Cable is an all-in-one data bridge that embeds a Prolific serial converter chip directly inside its USB Type-A housing. Instead of breaking out into a naked circuit board with pin headers, this module terminates in a 1-meter insulated cable with independent female jumper connectors. It acts as a virtual COM port on a computer, translating standard USB signals into low-voltage asynchronous serial data. This rugged form factor makes it the top choice for accessing headless Linux consoles on a Raspberry Pi, unbricking network routers, and flashing firmware onto set-top boxes.

✨ Key Features

Fully Encapsulated Form Factor: Houses the converter electronics safely inside the molded plastic USB connector shell, protecting the silicon from workbench shorts.
Direct Breadboard Interfacing: Terminated with four color-coded, 0.1-inch pitch female header receptacles to allow quick connection without loose wiring paths.
Tough Insulated Shielding: Outfitted with a flexible, 1-meter PVC protective jacket that safeguards internal signal paths against physical strain and tangles.
Low-Cost Diagnostic Tool

-25%

Click to enlarge

Back to products

Original price was: ₹200.00.Current price is: ₹150.00.

Characteristic	Specification Parameters
Embedded Controller IC	Prolific Technology PL2303HX / PL2303TA / PL2303GS
Host Computer Port	Standard USB Type-A Male Interface
Cable Length Profile	Approximately 1.0 Meter (3.3 Feet)
Logic Signal Threshold	3.3V TTL Level Logic (Standard model assignment)
Integrated Power Output	Fixed 5.0V DC output path pulled from host USB port
Supported Baud Rates	300 bps up to 1 Mbps or 6 Mbps (Depending on PL2303 generation)
Wire Terminal Interface	4 Pin Individual Female JST/Dupont Receptacles

Compare

Add to wishlist

Description

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “PL2303 USB to TTL Serial Converter Cable”

Shipping & Delivery

Related products

PL2303 USB to TTL Serial Converter Module

Converters

Characteristic	Specification Parameters
Core Controller IC	Prolific Technology PL2303 / PL2303HX / PL2303TA
Physical Input Interface	USB Type-A Male Plug
Supported Transmission Rates	300 bps up to 1 Mbps standard matching speed limits
Logic Threshold Level	3.3V / 5.0V Dual TTL compatible signals
Power Output Delivery	3.3V DC and 5.0V DC output paths
Data Transmission Buffers	128-byte inbound buffer / 256-byte outbound buffer
Status Monitoring	2 Onboard LEDs for real-time TX and RX traffic logging

Add to cart

Quick view

-38%

LM2596 DC-DC Buck Converter Step-Down Module

Characteristic	Specification Parameters
Regulator Topology	Monolithic Step-Down (Buck) Switching Regulator
Input Supply Voltage (VIN)	4.0V to 40.0V DC (Input must be at least 1.5V higher than output)
Adjustable Output (VOUT)	1.23V to 35.0V DC (Continuously variable)
Continuous Output Current	Up to 2.0A stable (Up to 3.0A maximum peak with an attached heatsink)
Fixed Internal Frequency	150 kHz Switching Clock
Output Ripple Voltage	< 30 mV peak-to-peak frequency ripple
Module Frame Footprint	Approx. 43 mm × 21 mm × 14 mm

-23%

Multi-Output DC-DC 12V to 3.3V / 5V / 12V Step-Down Power Module

Characteristic	Specification Parameters
Converter Circuit Form	Non-Isolated Multi-Rail Step-Down (Buck) Power Distribution Hub
Input Supply Voltage (VIN)	6.0V to 12.0V DC (12V recommended to ensure full pass-through tracking)
Available Output Rails	3.3V DC, 5.0V DC, and 12.0V DC Fixed Channels
Output Current Limit	~800 mA per individual low-voltage rail channel
Chassis Interface Format	Standard Red or Black Double-Sided PCB Layout
Onboard Voltage Regulators	AMS1117-3.3 (3.3V rail) and AMS1117-5.0 (5.0V rail) Linear Drops
Module Frame Footprint	Approx. 31 mm × 26 mm × 12 mm (Compact workspace profile)

-17%

MP1584 DC-DC Adjustable Step-Down Buck Converter Module

Characteristic	Specification Parameters
Converter Circuit Topology	Non-Isolated Step-Down (Buck) Switching Regulator
Input Supply Voltage (VIN)	4.5V to 28.0V DC (Input must remain at least 1.5V higher than output)
Adjustable Output (VOUT)	0.8V to 20.0V DC (Continuously variable scale)
Continuous Output Current	Up to 1.5A to 2.0A stable (Up to 3.0A maximum peak with short pulse durations)
Fixed Switching Frequency	Up to 1.5 MHz High-Speed Internal Clock
Maximum Efficiency Profile	Up to 92% Power Conversion Performance
Built-in System Protections	Thermal shutdown safety and cycle-by-cycle over-current limiting
Chassis Main Dimensions	Approx. 22 mm × 17 mm × 4 mm (Ultra-slim design)

XL4016 DC 10A 300W Step Down Buck Converter

Characteristic	Specification Parameters
Converter Circuit Core	XL4016E1 Non-Isolated Buck Switching Regulator
Input Supply Voltage (VIN)	7.0V to 40.0V DC (Input must be higher than target output)
Adjustable Output (VOUT)	1.2V to 35.0V DC (Continuously variable via CV trimmer)
Output Current Capacity	0.2A to 8A Continuous (Hits up to 10A Maximum with active fan cooling)
Maximum Output Power	Up to 300W Peak Performance Capacity
Fixed Switching Frequency	180 kHz / 300 kHz (Depending on exact board revision)
Output Voltage Ripple	~50 mV peak-to-peak frequency ripple
Chassis Dimensions	Approx. 65 mm × 47 mm × 24 mm

-20%

FT232RL FTDI USB to TTL Serial Converter Adapter Module

Characteristic	Specification Parameters
Core Protocol Chipset	FTDI FT232RL (Future Technology Devices International)
Physical Input Interface	Mini-USB Female Socket Port Link
Supported Data Rates	300 bps up to 3 Mbps maximum transmission speed
Operating Logic Voltage	Dual 3.3V or 5.0V DC Options (Jumper Selectable)
VCC Output Current Limits	5V mode: Up to ~500mA / 3.3V mode: Up to ~50mA
Host Operating Systems	Windows 10/11, macOS, Linux distributions, and Android
Pin Header Spacing	Standard 2.54 mm (0.1 inch) Pitch

XL4015 5A DC-DC Adjustable Step-Down Buck Converter Module

Characteristic	Specification Parameters
Converter Circuit Topology	Non-Isolated Step-Down (Buck) Switching Regulator
Input Supply Voltage (VIN)	8.0V to 36.0V DC (Input must remain at least 1.5V higher than output)
Adjustable Output (VOUT)	1.25V to 32.0V DC (Continuously variable scale)
Continuous Output Current	Up to 3.5A stable (Up to 5.0A maximum peak with an attached heatsink)
Fixed Switching Frequency	180 kHz Internal Oscillator Clock
Maximum Efficiency Profile	Up to 96% Conversion Performance
Built-in System Protections	Short-circuit current limiting protection and over-temperature thermal shutdown
Chassis Main Dimensions	Approx. 54 mm × 24 mm × 15 mm

CP2102 USB to TTL Serial Converter Module

Characteristic	Specification Parameters
Core Controller IC	Silicon Labs CP2102 USB-to-UART Bridge
Physical Input Interface	Micro-USB, Mini-USB, or Type-C Female Port (Variant dependent)
Supported Transfer Rates	300 bps up to 1 Mbps full hardware speed matching
Signal Logic Threshold	3.3V TTL Logic (Inputs are safely 5V tolerant)
Onboard Voltage Outputs	3.3V DC (up to 100mA max) and 5.0V DC (up to 500mA with self-resetting fuse)
Integrated Hardware Buffer	512-byte receive buffer and 512-byte transmit buffer
Module Outer Dimensions	Approx. 26 mm × 15 mm × 11 mm (Ultra-compact form factor)