Name: L298N Dual H-Bridge Motor Driver Module
SKU: VE-100
Availability: InStock

L298N Dual H-Bridge Motor Driver Module

Technical Specifications

Characteristic	Specification Parameters
Driver Driver IC	L298N Dual H-Bridge Power IC
Motor Supply Voltage (VMS)	5.0V to 35.0V DC (External power input)
Logic Supply Voltage (VSS)	5.0V DC
Peak Output Current	2.0A per individual channel (up to 3.0A peak surge duration)
Total Power Dissipation	25W (at max thermal capacity with integrated aluminum heatsink)
Control Logic Input Level	5V TTL and CMOS Compatible Logic inputs
Module Frame Footprint	43 mm × 43 mm × 27 mm

The L298N Dual H-Bridge Motor Driver Module is a high-power electronic switching board engineered to control the speed and direction of direct-current actuators. Built around the rugged L298N dual H-bridge driver IC, this module acts as a high-current buffer between low-power microcontrollers and inductive loads. It allows developers to control two independent brushed DC motors or one 4-wire bipolar stepper motor simultaneously, making it an essential component for robotic drivetrains and automated systems.

✨ Key Features

Dual H-Bridge Topology: Features two independent driver channels capable of reversing motor current directions to enable forward and backward rotation.
Onboard 5V Linear Regulator: Includes an integrated 78M05 voltage regulator that drops external motor power down to a stable 5V output to run low-power logic boards.
Flyback Protection Diodes: Equipped with high-speed protection diodes on all output lines to absorb inductive back-EMF voltage surges from stopping motors.
Granular PWM Speed Modulation: Supports pulse-width modulation signals on its enablement pins, allowing smooth, continuous speed throttle control.

-20%

Click to enlarge

Back to products

Original price was: ₹150.00.Current price is: ₹120.00.

Characteristic	Specification Parameters
Driver Driver IC	L298N Dual H-Bridge Power IC
Motor Supply Voltage (VMS)	5.0V to 35.0V DC (External power input)
Logic Supply Voltage (VSS)	5.0V DC
Peak Output Current	2.0A per individual channel (up to 3.0A peak surge duration)
Total Power Dissipation	25W (at max thermal capacity with integrated aluminum heatsink)
Control Logic Input Level	5V TTL and CMOS Compatible Logic inputs
Module Frame Footprint	43 mm × 43 mm × 27 mm

Compare

Add to wishlist

SKU: VE-100 Category: Motor Driver module

Description

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “L298N Dual H-Bridge Motor Driver Module”

Shipping & Delivery

Related products

L293D Dual H-Bridge Motor Driver Module

Motor Driver module

Characteristic	Specification Parameters
Driver Board IC	L293D Quadruple Half-H Power Driver Chip
Motor Driving Voltage (VCC2)	4.5V to 36.0V DC (External power input)
Logic Supply Voltage (VCC1)	4.5V to 7.0V DC (Typically 5V from logic controller)
Continuous Current Rating	600 mA maximum per individual channel
Peak Output Current Limit	1.2A per channel for short pulse durations
Thermal Protection Safety	Integrated automatic over-temperature thermal shutdown
Module Dimensions (approx.)	48 mm × 34 mm × 14 mm

Add to cart

Quick view

-17%

BTS7960 43A High-Power H-Bridge Motor Driver Module

Characteristic	Specification Parameters
Driver Configuration	Dual BTS7960 Half-Bridge Chips (Forming one Full H-Bridge)
Motor Supply Voltage (B+)	5.5V to 27.0V DC (External high-power battery or SMPS)
Logic Operating Voltage	5.0V DC
Continuous Current Rating	15A to 20A (Up to 43A maximum instantaneous peak surge)
PWM Frequency Limit	Up to 25 kHz (Supports smooth and precise duty cycles)
Output MOSFET RDS(on)	16 mΩ typical (Ultra-low internal resistance for low heat)
Module Frame Footprint	50 mm × 50 mm × 43 mm

-18%

PCA9685 16-Channel 12-bit PWM Servo Driver Module

Characteristic	Specification Parameters
Driver Controller IC	NXP PCA9685 16-Channel PWM/LED Controller
Communication Bus	I2C Protocol (Standard 100 kHz or Fast-Mode 400 kHz)
Logic Supply Voltage (VCC)	3.0V to 5.5V DC (Compatible with 3.3V and 5V systems)
Servo Supply Voltage (V+)	Up to 6.0V DC Max (External high-current power input)
PWM Resolution Output	12-bit (4,096 distinct timing increments)
Adjustable Frequency	24 Hz to 1,526 Hz (Configurable for servos or LEDs)
Module Frame Footprint	62 mm × 25 mm

A4988 DMOS Microstepping Stepper Motor Driver Module

Characteristic	Specification Parameters
Driver Driver IC	Allegro A4988 Microstepping Driver Chip
Motor Supply Voltage (VMOT)	8.0V to 35.0V DC (External power rail for driven actuators)
Logic Supply Voltage (VDD)	3.0V to 5.5V DC (Fully compatible with 3.3V and 5V microchips)
Continuous Output Current	1.0A per phase winding (Up to 2.0A with attached heatsink and active cooling)
Microstep Resolutions	Full-step, Half-step, Quarter-step, Eighth-step, and Sixteenth-step
Onboard Fault Protection	Thermal shutdown, crossover-current protection, and under-voltage lockout
Module Dimensions (approx.)	20 mm × 15 mm × 11 mm (Ultra-compact DIP carrier form factor)

-52%

DRV8833 Dual H-Bridge DC Motor Driver Module

Characteristic	Specification Parameters
Driver Driver IC	Texas Instruments DRV8833 Dual H-Bridge Chip
Motor Supply Voltage (VM)	2.7V to 10.8V DC (Ideal for Li-Ion, NiMH, or AA battery packs)
Continuous Output Current	1.2A per individual motor channel (at 25°C room temperature)
Peak Pulse Current Limit	2.0A per channel for short pulse durations
Control Logic Input Level	3.3V and 5V Logic Compatible (Works with Arduino, ESP32, Raspberry Pi)
PWM Frequency Support	Up to 50 kHz for smooth speed adjustments
Module Dimensions (approx.)	18.5 mm × 16 mm × 3.5mm

DRV8825 Microstepping Stepper Motor Driver Module

Characteristic	Specification Parameters
Driver Driver IC	Texas Instruments DRV8825 Motor Driver
Motor Driving Voltage (VMOT)	8.2V to 45.0V DC (External motor power feed)
Logic Working Voltage	0V to 5.5V DC (Does not require a separate VCC logic pin)
Continuous Output Current	1.5A per phase winding (Up to 2.2A with active cooling fan/heatsink)
Microstep Resolutions	Full-step, 1/2, 1/4, 1/8, 1/16, and 1/32 steps (3 Selectable Pins)
Hardware Safety Checks	Over-temperature shutdown, over-current fault, and short-circuit protection
Module Dimensions (approx.)	20 mm × 15 mm × 11 mm

TB6600 4A Stepper Motor Driver Controller

Characteristic	Specification Parameters
Driver Topology Type	Bipolar Constant-Current H-Bridge Chopper Drive
Input Operating Voltage	9.0V to 42.0V DC (12V to 24V DC highly recommended)
Adjustable Peak Current	0.5A to 4.0A Max (8 selectable current steps via DIP choices)
Microstep Resolutions	1, 2/A, 2/B, 4, 8, 16, 32 (Up to 6400 pulses per single revolution)
Control Signal Input Level	3.3V to 24.0V DC (Fully logic compatible with 5V Arduino / 3.3V ESP32)
Maximum Pulse Frequency	Up to 200 kHz
Onboard Fault Protection	Over-temperature parking, over-current, under-voltage, and short-circuit protection

ULN2003 Driver

Characteristic	Specification Parameters
Driver Driver IC	ULN2003A (High-Voltage, High-Current Array)
Operating Input Voltage	5.0V to 12.0V DC (Power supply lines isolated from logic inputs)
Max Output Sinking Current	500 mA per channel (Peak current capacity up to 600 mA)
Max Output Standing Voltage	50V DC Peak
Compatible Motor Styles	4-Phase, 5-Wire Unipolar Stepper Motors (e.g., 28BYJ-48)
Logic Control Formats	5V CMOS and TTL Level Logic Inputs
Module Dimensions (approx.)	35 mm × 32 mm × 10 mm